#01 - Brake Lines - PHR Pro-Street stainless steel braided upper and lower brake lines are a terrific upgrade! Those 30-year-old stockers just won't "cut it" on a HOT Street-bike! - $49.00 Ea.
#02 - Disc Brake Rotors - Pro-Street Brembo style spiral-drilled front disc brake rotors. (H1/H2) Very "Trick!", super lightweight and very efficient! These rotors, when used with our STAINLESS steel braided hoses and Brembo Pads, RIVAL the dual DISC performance!
#03 - Disc Brake Pads - High performance disc brake pads (Brembo & Ferodo)
#04 - Lock Tabs - Disk brake lock tabs. (H1/H2) - $5.00 Ea.
#05 - Brake Shoes - High Performance brake shoes. (H1/H2) - $49.00 (Per set)
#06 - Master Cylinder Overhaul Kit - (All Models) - A GREAT safety upgrade for your Triple. Remember, the rubber in the master cylinder is 30 years old! - $39.00
#07 - Caliper Rebuild Kits - (H1/H2) - Don't trust your life to worn calipers! $49.00
#08 - Caliper Pistons - (H1/H2) - VERY RARE, NEW and priced right! - $59.00 Ea.
#09 - Fork Braces - Billet polished aluminum fork braces. (H1/H2) "Top Shelf" quality. These braces will eliminate inherent high-speed wobble and look very "Trick"!
#10 - Fork Air Caps - Billet aluminum fork air caps. (H1/H2) Tune-up the PHR way!
#11 - Fork Seals - (All Models) - Fresh stock from Kawasaki, not "new old stock" found sitting on the shelf for years getting harder every day. - $10.00 Ea.
#12 - Fork Oil - Bel-Ray Synthetic 10-WT fork oil. $10.00 (Per Liter)
#13 - Fork Dust Boots - New, fresh Stock! - (All H2/Late H1) VERY HARD to find. Replace those hard, cracked boots now!
#14 - Steering Head Bearing Kits - Tapered steering head bearing kits. (All Triples) Check out our LOW PRICE! These kits are an absolute "must" for your Triple! $42.00 (Per set)
#15 - Swing arm Kits - Extended swing arm kits. (H2) A "must" on all high horsepower H2's!- SORRY, NO LONGER AVAILABLE.
#16 - Swing arm Bushings - Bronze swing arm bushings. (All Models) A "must" on Pro-Street Triples! and 1/2 the cost of those flimsy stockers. Installed in every Pro-Street Triple we do!
#17 - Rear Sets - Dunstall Pro-Street H1 rear sets. (73-76 H1) The best way to put some nostalgia, "era correct" rear sets on your H1! Very rare, limited quantities. - SORRY, NO LONGER AVAILABLE.
#18 - Handlebars - Stock handlebars. (69-71 H1/72 H2) New, beautiful, chrome plating. - $89.00
#19 - Sprocket Kit - PHR chain and sprocket kit. (All Triples) Call for super prices! We split our discount on all sprockets and chains with you, and you SAVE BIG!
#20 - Rear Sprocket Lock Tabs - (H1/H2) - $8.00 Ea.
#21 - Handlebars - PHR custom handle bars. (All Triples) Medium rise ...the very best available! These 2-inch rise bars are perfect, and we've tried them all! - $49.00
#22 - Handlebar Grips - Original Kawasaki grips. Very rare! New, fresh "soft stock".
#23 - Front Sprocket Lock Tabs - (All Models) Don't trust Loc-Tite only; use a new lock tab! - $6.00 Ea.
#24 - Steering Damper - (Brand NEW!) Your damper must be kept in new condition to properly absorb and prevent wobble. Priced at 1/2 Kawasaki list!
#25 - Wheel Rims - DID and Sun custom aluminum front and rear rims. (VERY Trick!) Our rims are priced lower than stock Kawasaki rims! These are a great way to make your Triple unique. Use our stainless spoke sets to lace them up!- SORRY, NO LONGER AVAILABLE.
#26 - Spoke Sets - Stainless steel 80-piece spoke sets. (H1/H2) We even stock sets for the early H1 drum brake front wheels.
#27 - Rear Shocks - Pro-Street custom rear shocks. (Heavy duty springs available.) Priced at 1/2 the cost of new factory shocks ...only at PHR! All show quality chrome plated with 5-way adjuster. You can't go wrong with PHR Pro-Street shocks. NO LONGER AVAILABLE
Engine Parts
[Suspension] [Engine] [Body] [Pro-Street Gear]
#28 - Custom Porting - Pro-Street, Stage I, and Stage II custom porting. (All Triples) PHR delivers BIG, BIG STREETABLE horsepower ...from 90-180 HP on H2's! (Also See Custom Rebuilds)- SORRY, NO LONGER AVAILABLE.
#29 - High Compression Pro-Street Heads - (A "powerful performance upgrade" for All Triples!) These are the HOT setup for STREET or STRIP! Machined for pump or race gas, they look VERY "Pro" and produce very high horsepower. These heads are not "just machined"; they're 3-stage media blasted, crack checked, and chambers fully polished and CC'ed! (See Custom Rebuilds)
#30 - Aluminum Race Heads - Custom welded aluminum race heads. (All Triples ) Very Pro! Available in "BUTCH CUT" style for a great look. These heads don't crack under severe use! Butch Cut heads add a unique, VERY COOL look to your motor, and are given the "FULL TREATMENT", not just machined and sent back as is.
#31 - Piston Kits - Wiseco Pro-Lite piston kits. (H1/H2) - Call for Super Prices!
#32 - Wrist Pins - Wiseco Super-Lite wrist pins. (30% lighter than stock!)
#33 - Rod Kits - ( H1/H2) These are brand new and offer a 50% savings over Kawasaki list price. NO LONGER AVAILABLE
#34 - Crankshaft Seals - Crankshaft inner and outer seals. Fresh stock. ( H1/H2)
#35 - Main Bearing Sets - Crankshaft main bearing sets. Very hard to find! ( H1/H2)
#36 - Upper Rod Bearings - ( All Triples)
#37 - Pistons - Wiseco "Super-Lite" Forged S-2 pistons. Very rare, assorted sizes, but limited quantities.
#38 - Pistons & Rings - Genuine Kawasaki Brand stock factory pistons and rings. (H1/H2 & S1/S2) Sizes and quantities are limited.
#39 - Head Gaskets - PHR custom Cometic copper head gaskets.(H1/H2 - All Sizes) -10.00 Ea.
#40 - Head Gaskets - PHR Pro "Big-Bore" re-useable head gaskets. (H1/H2) Never use stock Kawasaki head gaskets if you've bored +.040 oversize. - NO LONGER AVAILABLE
#41 - Cylinder Studs - Cylinder intake and exhaust studs. (All Models) -SORRY, NO LONGER AVAILABLE.
#42 - Base Gaskets - PHR custom Cometic base gaskets. ( H1/H2) - $4.00 Ea.
#43 - Cometic Gasket Sets - Stock Cometic 16-piece gasket sets. ( All Triples) Terrific savings! PHR sells the entire gasket set for the price of the head gaskets alone from Kawasaki!
#44 - Seal Kit - Engine overhaul internal seal kit. ( H1/H2) Genuine Kawasaki Brand!
#45 -Shift Shafts - Modified shift shafts. (H1/H2 ) Easy install and Very Trick! Give your H1 or H2 that new Super-bike shift feeling!
#46 -Clutch Assembly - Pro-Street 15-plate race clutch. ( H2) Great for street use, easy clutch lever effort, and handles 155 horsepower Stage III with no problems!
#47 - Clutch Actuators - ( All Models) We carry the steel roller bearing style in NOS. New Sy-Tech actuator now available, very trick!
#48 - Clutch Hubs & Pressure Plates - Modified clutch hubs and pressure plates for 15-plate clutches. (H2)
#49 - Roller Bearing Clutch Pushers - (H1/H2) Stops "friction welding" problems. These are the latest style "Pro" units, not the Torrington style "cheapies".
#50 - Clutch Packs - Stock and HIGH PERFORMANCE clutch packs. ( Most Models ) NO OFFBRAND JUNK! Freshen up your clutch with quality parts from PHR - SAVE 20% compared to Kawasaki list price.
#51 - Clutch Springs - High performance and stock clutch springs. ( All Triples ) Priced at 35% under Kawasaki list!
#52 - Carburetors - Mikuni race.. All sizes at super-savings, prepped and jetted!- SORRY, NO LONGER AVAILABLE.
#53 - Main Jets & Rebuild Kits - Mikuni main jets, power jets, rebuild kits and performance manuals.
#54 - Carburetor Floats - NEW Mikuni brass carb floats. ( H1/H2) Very hard to find and a critical part in those carbs! Don't trust those old floats, replace them now!
#55 - Carburetor Manifolds - New Kawasaki Brand rubber carb manifolds. H2 ONLY
#56 - Carburetor Manifolds - New Mikuni rubber carb manifolds. (H2) Super prices! Save BIG compared to stock Kawasaki manifolds!
#57 - Manifold Kits - Custom Billet intake manifold kits. ( H1) Available only from PHR! These kits allow the use of H2 carbs or 34mm Mikunis on your HOT H1!- SORRY, NO LONGER AVAILABLE.
#58 - Intake Manifolds - Custom Tunnel Ram Pro Stock aluminum intake manifolds. ( H2) STEP UP to Stage III porting without expensive cylinder machining procedure.- SORRY, NO LONGER AVAILABLE.
#59 - Intake Manifolds - Custom stock style Hi-Flo intake manifolds. ( H1 ) These manifolds flow an additional 20% over stock. Gives your H1 the edge over the competition!- SORRY, NO LONGER AVAILABLE.
#60 - Air Inlet - 3-into-1 rubber air inlet. ( H1/H2) Genuine Kawasaki Brand tubes from carbs to air box can. Fresh, soft, new stock, and priced right!
#61 - Manifold Gaskets - PHR custom Cometic intake manifold gaskets. ( H1/H2)
#62 - Velocity Stacks - Mikuni spun-aluminum polished 34mm velocity stacks. (Screens included at NO CHARGE!) Stacks are custom made to fit 34mm Mikunis.
#63 - Velocity Stacks (For Stock Carbs) - Spun aluminum polished velocity stacks. ( H1/H2)ULTRA rare, and found nowhere else in the U.S.! Give a bit of that NOSTALGIC RACE look to your H1 or H2. These stacks include FINE brass screens at NO CHARGE! You'll really hear those Mikunis SCREAM with these Pro stacks! - SORRY, NO LONGER AVAILABLE.
#64 -Master Carb Overhaul Kit - ( All Triples) Genuine Kawasaki Brand ...NO OFFBRAND JUNK! An absolute "must" on all Triples. Would you drive your own street car with a 30-year-old dirty and worn out carb? Freshen up those carbs now with these 12-piece MASTER KITS!
#65 -High-Flo Pingel Petcock - (H1/H2) Eliminate the "leak-prone" stocker! Free fuel line included at NO CHARGE from PHR!
#66 - Petcocks - New High-Flow petcocks ( All S-Series ) S-Series owners, get yours now. Don't trust that 30-year-old "stocker" that can't be rebuilt. Get yours now! FREE fuel line included.
#67 - Fuel Line Kits - Clear available only. (All Triples)
#68 -Petcock Overhaul Kits - ( All H1/H2) Very hard to find! The perfect safety upgrade for your bike! The rubber seals in your stock petcock get hard and leak over time! Don't gamble with a dangerous fuel leak. Rebuild that petcock and be safe! - $39.00 (Per kit)
#69 - Gas Cap Gaskets - (All H2/Late Model H1/All S-Series ) Save that paint job, keep the gas off the paint and in the tank with our high quality rubber gaskets! - $7.00
#70 - Air Filters - Chrome K&N High-Flo filters! ( Styles for every Triple ) Our prices are the best around. Call, fax, or email for the information on our full line of K&N's.
#71 - Air Can Filters - PHR HIGH-FLO LIFETIME foam air filters forStock H2 air cans. Priced right!
#72 - Air Can Filters - K&N High Flo Lifetime stock air can filters. (H1/H2) Next best thing to running the individual filter pods. These filters are cleanable and flow 20% more air than the "stockers". A great upgrade!
#73 - Expansion Chambers - PHR custom expansion chambers (black.) ( H1/H2) Best fit and performance available! These chambers make big horsepower, sound very cool, and fit great! FREE installation kit and jet kit included. ($35.00 Value)
#74 - Muffler Seals - Exhaust system "high-temp" rubber muffler seals. (All Triples) Fresh stock, don't contend with leaking, dripping mufflers. Replace those seals now!
#75 - Oil Pump Oil - Bel-Ray SI-7 oil pump oil.BIG LITER BOTTLE - $10.00
#76 - Exhaust Rings - PHR custom-made copper exhaust rings. ( All Models) Stop those ugly leaking pipes! Priced out 50% under Kawasaki list!
#77 - Oil Pump Crush Washer Kits - ( 1/2 PRICE ) Remember, crush washers can be used only once.) DON'T GAMBLE! When any oil Banjo bolt is loosened, it is MANDATORY to replace both soft crush washers. Don't let air into that system, and DON'T put up with leaks!
#78 - Oil Pump Block-Off Kits - ( All Models) An absolute "must" for all pre-mix Triples! This 12-piece kit is priced right! -$19.00
#79 - Stock Phillips Head Case Bolt Sets -(All Triples) 18-piece zinc plated Genuine Kawasaki sets. - $24.00
#80 - Custom Allen Head Case Bolt Sets - (All Triples) A great visual upgrade to your Triple. 18-piece set includes wrench. A popular item and priced to sell! -$24.00
#81 - Plug Wire Sets - PHR Pro-Street plug wire sets. ( All Triples) The H2 kits contain new NGK splicers that let you replace those old black coil spark plug wires professionally. - $39.00 (Per kit: H2) $29.00 (Per kit: All others)
#82 - Spark Plug Caps - NGK Pro spark plug caps. ("No resistance") - $6.00 Ea.
#83 - Spark Plugs - NGK! (H1/H2) - $3.00 Ea.
#84 - Service Manuals - H-Series Kawasaki shop service manuals. This is the most important part or accessory you could ever buy for your Triple. Don't be without one! Includes full color wiring diagrams. - $45.00
#85 - Service Manuals - A-Series Kawasaki service manuals.VERY RARE and includes early H1 information. A "must" have for professional repairs or restorations. - $45.00
#86 - Service Manuals - S-Series Kawasaki service manuals. Hard to find, new and in stock at PHR! - $45.00
#87 - Media Blasting - Custom 3-stage media blasting. Available for cases, cylinders, heads, and covers...all atSUPER PRICES. A very, very popular Pro-Street visual upgrade. PHR can also duplicate that "NOS" new look for you restoration guys and gals! We use oxide, glass beads, and walnut shells in three separate steps to create a beautiful finish! ( Also See Custom Rebuilds )
#88 - Points & Condensers (H1/ALL "S" Series)
#89 - Boyer Bransden Ignition Systems - ( S-Series ONLY) The best available!
#90 - Battery Eliminator - (H2) Don't just end dead battery aggravation ...eliminate it! SORRY, NO LONGER AVAILABLE
#91 -Emergency Tool Kit - ( All Triples) Replaces original kit from factory. Save embarrassment, pushing, or towing bills. Don't be caught without one! - $49.00
#92 - Cables - (Most Models ) Genuine Kawasaki Brand. We share our discount with you on all Genuine Kawasaki cables. For you early model H1 riders, we've got those RARE gray cables in stock too. Be safe ...be smart ...upgrade to new cables soon!
Body Parts
[Suspension] [Engine] [Body] [Pro-Street Gear]
#93 - Seat Covers - ( Most Models) "Professional Quality" reproduction seat covers "just makes" the bike. Easy to install, and an absolute "must" on all restorations!
#94 - Decal Sets - ( All H2/Most H1/Some S-Series) These reproduction decal sets are the "best of the best" professional quality!
#95 - Swing arm Stands - ( H2 ONLY) These custom stands are a "must" for expansion chamber equipped bikes andVERY Trick! You have seen these used during "pit stops" on TV when watching the Pro road race bikes.- SORRY, NO LONGER AVAILABLE.
#96 - Side Covers - ( 72-73 H2 ) Heavy-duty fiberglass. Top quality direct bolt on, and WILL NOT crack!- SORRY, NO LONGER AVAILABLE.
#97 - Tank Mount Rubber Isolators & Pads - (All H2)
#98 - Side Cover Rubbers - (All H2/Most H1 and S-Series) New stock! - $6.00 Ea.
#99 - Mirrors - ( Most Models) Kawasaki Brand. - $29.00 Ea. (Right and Left Hand)
#100 - Kicker Rubbers - ( All Models) -$7.00 Ea.
#101 - Headlight Rims - ( H2) Brand new chrome rims at great prices! -$39.00
#102 - Shifter Rubbers - (All Models) - $5.00 Ea.
#103 -Halogen Headlight Kit - (H2/KH500 - $89.00 - Per Kit)
#104 - Headlight Bucket Ground Pieces - NEW!
#105 - Turn Signal Assemblies - ( All H2/72-S2) These are the complete turn signal chrome heads with lenses and wiring...everything except the stem.
#106 - Turn Signal Stems - ( Most Models)
#107 - Gauge Cups - Professionally reconditioned and "wrinkle painted" gauge cups. These are a beautiful upgrade on any 72-73 H2 restoration!- SORRY, NO LONGER AVAILABLE.
#108 - Turn Signal Lens - ( Most Models)
#109 - Taillight Lens - (69-71 H1) Super prices!
#110 - Taillight Lens - ( 73 H1-76 KH500) Super prices!
#111 - Taillight Lens - (74-75 H-2) Super prices
#112 - Tail Piece Mole Kits - ( 72-73 H2/72 S2 ) These are "dead on" perfect replacements for the factory moles. Check out our prices. -$19.00 Ea.
#113 - Motorcycle Covers - ( All Models ) Great prices!- SORRY, NO LONGER AVAILABLE.
#114 - Seat Foams - (69-71 H1) ONLY at PHR! Make your Triple look and feel brand new! Your butt will thank you! LIMITED QUANTITIES!
